Jensen Mobile Multimedia AM/FM/DVD Receiver VM9410 User Manual download pdf (Page 13)

VM9410

OPERATING INSTRUCTIONS

Power On / Off

Press the /MUTE button (1) to turn the unit on. The buttons

on the front of the unit light up and “WELCOME” appears

briefly in the LCD panel (17), followed by the current mode

status. If the TFT screen is open, only the current mode

status is displayed. You can also turn on the unit by pressing

the OPEN button (2) and opening the TFT screen.

Press and hold the /MUTE button (1) on the front panel or

the POWER button (#) on the remote to power off the

unit.The monitor is drawn back into the main compartment

and the LCD screen displays “BYE-BYE”.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The

beep tone cannot be disabled.

Mute

Press the /MUTE button (1) on the front panel or the MUTE

button (3) on the remote to mute the volume from the unit.

Press the MUTE button again to restore the volume. “MUTE”

is displayed on the LCD monitor. Adjusting the volume or

using any of the audio set-up features cancels the mute

function.

Playing Source Selection

Press the SRC/P.MODE button (15) on the front panel or the

SRC button (8) on the remote to change between available

playing sources in the following order: TUNER, DVD, CD

Changer, AUX IN or CAMERA (rear view video camera). The

playing mode is displayed on the TFT and LCD screens.

AUX IN Mode

An external peripheral device can be connected to this unit

via RCA output and “AUX-IN”.

CAMERA Mode

“CAMERA” mode is only available if the camera is connected

and during reverse driving. To install a rear view video

camera, connect the video input cable to the camera output

cable.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY

ENCODER (6) on the front panel or press the VOL+/ VOL-

buttons (15, 16) on remote control. When the volume level

reaches “0” or “40”, a beep sounds, indicating that the

adjustment limit has been reached. The volume ranges from

“0” to “40”. The LCD or TFT screen displays the volume level

for 3 seconds.

Audio Control Menu

The Audio Control feature allows you to easily adjust your

audio system to meet the acoustical characteristics of your

vehicle, which vary depending on the type of vehicle and its

measurements. To get the best possible sound quality from

your new system, be sure to adjust the settings for the

speakers as well. Proper setting of the Fader and Balance

boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the VOL/LOC/DX knob (6) on the front panel once to

display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Continuously press the VOL/LOC/DX knob (6) on the front

panel, or press the ( )/( ) buttons (14, 22) on the remote

control or the ( )/( ) buttons (18, 19) on the joystick to

select the audio feature to be adjusted.

Adjusting an Audio Feature

Rotate the VOL/LOC/DX knob (6), press the ( )/( )

buttons (17, 19) on the remote control, or press the ( )/( )

buttons (16, 17) on the joystick to adjust the selected feature

to the desired setting.

NOTE: The Bass and Treble levels are only adjustable

when EQ is set to “User” mode.

The Loud function compensates for deficiencies in sound

ranges at low levels. Loudness levels range from 1-4 or “off”.

When the Loud function is on, LOUD is displayed on the

screen.

Exiting the Audio Control Menu

Press and hold the VOL/LOC/DX knob (6) or stop making

adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker,

please refer to “Surround Setup” on page 19.

Rear Zone

If a monitor is installed in the rear zone and connected to the

rear zone AV output, passengers in the back seat can control

the DVD output using the rear zone remote control. See

“Rear Zone Remote COntrol” on page 9 for instructions.

System Reset

To correct a system halt or other illegal operation, use the tip

of a pen to press the RESET button (22) located on the front

bottom-right corner of the unit. After a system reset, the unit

restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD

resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a

telephone call is received by the car phone or when verbal

navigation is performed.

Table 5: Audio Adjustments

Audio Function Adjustable Range

EQ User

Flat

Jazz

Pop

Classical

Treble -7 to +7

FADE -7 to +7

BAL -9 to +9

SUB.W -9 to +9

Loud Off, 1-4

Table 6: 6-Channel Audio Adjustments

Item Adjustable Range

Master Volume 00 to 40

Front Left Channel Volume -10 to +10

Front Right Channel Volume -10 to +10

Rear Left Channel Volume -10 to +10

Rear Right Channel Volume -10 to +10

Center Channel Volume -10 to +10

Subwoofer Volume -10 to +10

[RESET] Button

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 24 25

Comments to this Manuals

No comments

Jensen Mobile Multimedia AM/FM/DVD Receiver VM9410 User Manual Page 13

Comments to this Manuals

Related products and manuals for Car Video Jensen Mobile Multimedia AM/FM/DVD Receiver VM9410