Jensen BT-390 User Manual

BBlluueettooootthh HHaannddssffrreeee CCaarr KKiitt wwiitthh LLCCDD DDiissppllaayy User’s Manual Model: BT-390

2. Installation q Preparing the remote control The control module is designed to attach to the inside of the steering wheel on the left or right side.

2. Installation Attaching the remote control Refer to the following to attach the control module: 1. Attach the rubber clasp to the two notches on on

2. Installation 4. Attach the bracket cover with the two supplied hex bolts. 5. Slide the control module into the module bracket as shown. (To remo

2. Installation r Installing the Caller ID Display The caller ID is designed to sit on the dashboard or other location. Once it is attached to the sta

2. Installation s Installing the Microphone Before installing the microphone, take note of the following:  Make sure that the cable can reach from t

11 3. Operation n How to Operate the Car Kit Understanding the icons on your screen and remote control Please see below for the explanations of the i

3. Operation o Basic operation Connecting to the Mobile Phone for the First Time As soon as the ignition is turned on “BT-390” text will be displayed

3. Operation 13 p Dialing the First Call Scroll down to enter main menu and go to Dial Number then press the Enter button. Scroll up/down to go to you

3. Operation 14 There are a number of ways to upload your phonebook to the BT-390, if your mobile phone supports automatic phonebook synchronization (

3. Operation 15 Name & Numbers Sync Phone Book Receive Contact Back Note: Contacts are picked up in random order by the car kit; therefore, BT-39

Contents Bluetooth Handsfree Car Kit with LCD Display················ 3 1. Introduction·····························································

3. Operation 16 screen will display the contact received. Repeat the process for other entries if necessary. Once you have finished, press the Reject/

3. Operation 17 Accessing Received, Dialed, and Missed Calls BT-390 can sync with your mobile phone’s call history. To access the previously dialed ca

3. Operation 18 To initiate the private call function, simultaneously press both scroll buttons on the remote control during a call. Once activated, p

3. Operation 19 Viewing, Connecting, and Deleting Previously Paired Phones You can re-establish a connection with a previously paired phone by enterin

3. Operation change to a different language simply follow the following steps: Settings → Language Setup → English Note: Available languages: Englis

3. Operation Settings → Display Settings → Contrast → +/- Contrast Adjusting Display Brightness You can adjust the backlight level of the LCD displ

3. Operation R G B Enabling Auto Dim Screen You can enable or disable the backlight to go dim when the system idle time is longer than 10 seconds:

3. Operation Finding Out the Device Software & Firmware Version For information about the device, go to: Settings → About Car Kit BT-390 S/W V 2.5

3. Operation FM User 2 FM Disable To enable or disable handsfree function via FM transmitter: Settings → Sound Settings → H.F. Out F.M. → Enable/Dis

3. Operation Use the Media Menu buttons to Play, Pause, jump to Previous or Next songs, and Stop playing. Shortcut Key: Alternatively, press the Up

u Display Settings·································································· 20 Adjusting Display Contrast··································

3. Operation Factory Settings Reset BT-390 allows you to master reset the car kit back to the original factory settings. To master reset BT-390 plea

3. Operation 27 Troubleshooting My mobile phone can’t make a connection. Make sure the bluetooth function on your phone is enabled. Make sure the car

3. Operation 12 MONTH LIMITED WARRANTY Applies to Jensen Series Mobile Electronics. AUDIOVOX Electronics Corporation (the Company) warrants to the or

1 Carefully unpack the BT-390 Bluetooth Handsfree Car Kit and check that the following items are included: n Identifying Components Unpack the Car Ki

3 2. Installation This section demonstrates how to set up and install the BT-390 into a vehicle. n Installing the Junction Box The Car Kit is designe

2. Installation o Connecting the Power Supply (For Options 1 and 2 only) The following illustration demonstrates how to connect the Car Kit’s power ca

2. Installation p Connecting Components The following illustration shows where to connect the components. 5 Item Description Caller ID The caller